AMPP Cathodic Protection Tester (CP1) Certification Practice Exam

These questions are part of the practice quiz. Start practicing

• What is the efficiency percentage of a zinc anode?
• What are drain bonds or cables also known as?
• What code is associated with internal CP systems in oil treating vessels?
• What phenomenon can cause corrosion to occur in structures?
• What characteristic of steel makes it highly susceptible to corrosion?
• How is the average soil resistivity calculated in the Wenner method?
• Which principle is used in cathodic protection to prevent the corrosion of a metal surface?
• Before installing an interrupter in a rectifier, what is required by code?
• What does a higher current level indicate in terms of potential corrosion rates?
• According to Kirchhoff's law, what is true about voltages in a circuit?
• What is a primary method for assessing the risk of corrosion in structures?
• In electrochemistry, what is oxidation primarily associated with?
• If a diode check reading shows OL on both sides, what does this indicate?
• What is the purpose of the code SPO169?
• Metallic shorts to a structure with cathodic protection will typically result in what?
• What are mitigation bonds also referred to as?
• What effect would increased current have on the corrosion rate?
• What is the primary purpose of anodes in cathodic protection?
• What is a common function of cathodic protection systems?
• A protective coating should ideally have what characteristic?
• Part 195 of the regulations is primarily associated with which type of infrastructure?
• Which arrangement is considered more desirable for cathodic protection?
• In cathodic protection systems, which quality is preferred for anodes?
• Which type of measurement is crucial for assessing the effectiveness of a CP system?
• How is current defined in electrical circuits?
• Why is it important to control stray current in cathodic protection systems?
• What direction does conventional current flow through an electrolyte?
• Which of the following is a common measure to prevent corrosion?
• When dealing with ICCP in atmospherically exposed concrete structures, which steel specification is relevant?
• What best describes dynamic stray currents?
• Is it true that ICCP is used for poorly coated structures?
• Compared to an impressed current system, a galvanic anode system in soil has which of the following advantages?
• What measurement indicates effective corrosion control in a cathodic protection system?
• Graphite anodes perform well in which type of soil?
• Cathodic protection measures involve the potential difference between which two entities?
• What determines the depth of measurement in the Wenner Four-Pin Method?
• What happens to the pH of the environment around the cathode during cathodic protection?
• What occurs during the cathodic protection process at the cathode?
• What is the role of an anode in a corrosion cell?
• What is an electrolyte?
• As cathodic protection works, what does the cathode become more?
• How does the potential of aluminum anodes typically compare to other anode materials?
• The quantity of polarization is determined by?
• Which factor does NOT affect resistance in a conductor?
• What component is NOT typically included in a galvanic anode system?
• In terms of electrical charge, what is more important than size?
• Which material is often used for sacrificial anodes in cathodic protection systems?
• How do corrosion rates typically respond to increasing temperature?
• Which process can create interference in cathodic protection systems?
• What is typically the purpose of using amusement park rides as a method of cathodic protection?
• What is the effect of cathodic protection on the structure regarding its electronegativity?
• Which voltage drop is considered uncontrollable?
• What term describes current that does not follow the intended path?
• What is the force that holds atoms together in chemical bonding?
• In what type of environment is ICCP particularly utilized?
• Under what condition do amphoteric metals not corrode?
• What are molecules composed of?
• Do ions exist in the electrolyte during corrosion processes?
• What type of reference electrode is classified as pseudo?
• What is the purpose of impressed current cathodic protection in corrosion control?
• What is the standard unit of measure for conductivity?
• What kind of anode is commonly used for cathodic protection in marine environments?
• What currents are associated with sunspot activity and disturbances in the Earth's magnetic fields?
• Voltage is defined as an __________ force.
• In the Wenner Four-Pin Method, what does the average soil resistivity depend on?
• Which anode system is characterized by high consumption rates?
• What code applies to impressed current cathodic protection of internal submerged steel water storage tanks?
• What is the minimum requirement for cathodic polarization in order to effectively control corrosion?
• Which type of anode was primarily developed for use in seawater?
• What is recommended for the distance between the pipe and anodes for effective operation?
• What type of electrodes are used in cathodic protection systems to provide a protective current?
• Liquid pipelines fall under which part of the CFR regulations?
• Which of the following best describes an anion?
• What are the primary components of a corrosion cell?
• Which type of metal is known to corrode in an alkaline environment?
• Which condition would most likely result in increased resistivity?
• In a circuit, what does a high resistance indicate about the flow of current?
• Why is it important to measure the case-to-ground voltage of a rectifier?
• What effect does a metallic short have on circuit resistance?
• When using the Wenner 4-pin method, what do you measure for your calculations?
• What term describes an ionized solution capable of conducting electricity?
• What are often used to check cathodic protection on pipelines and made of the same material as the one being tested?
• What is the potential of zinc anodes used in cathodic protection?
• The criterion of -850mV is referenced to which electrode?
• Which reaction does cathodic protection primarily aim to prevent?
• What term describes the production of hydroxyl ions during the cathodic process?
• Which of the following statements about corrosion is true?
• Which type of cathodic protection is preferred for poorly coated structures in high resistivity soils?
• What is a common result of sunspot activity?
• What material is used to surround anodes in their bed?
• Which code applies to underground storage tanks protected by cathodic protection?
• Which reference electrode is predominantly used in seawater?
• What is a common sign of a malfunctioning CP system?
• In terms of electrical properties, a cathode exhibits what type of characteristic?
• What is the efficiency percentage of a magnesium anode?
• A system used to protect pipelines from corrosion is known as what?
• What code relates to external cathodic protection of on-grade metallic storage tank bottoms?
• What type of coatings are noted as original coatings from Europe?
• A high concentration of hydrogen atoms will have what effect on pH?
• In cathodic protection testing, what does a lower soil resistivity indicate?
• What does the term 'electrolyte' refer to in a corrosion cell?
• Metal in the vicinity of higher concentrations of oxygen will be more:
• If a multimeter reads "0.001" while testing both sides of a diode, what does this signify?
• Which methods can be used to test for a short circuit?
• What is the general anode efficiency rating of aluminum?
• To effectively mitigate corrosion, what is often used in conjunction with a protective coating?
• When taking a pipe to soil reading over a structure, what is typically located over the pipe?
• What is the code for Control of External Corrosion on Underground or Submerged Metallic Piping Systems?
• What is the main cause of corrosion in metals?
• Surface groundbed anodes are typically buried at what depth?
• What does increased polarization indicate about a metal surface?
• What do anodes do with current?
• What do Close Interval Potential Surveys measure?
• Which of the following describes the flow of conventional current in a circuit?
• What type of current must be maintained to ensure effective stray current mitigation?
• What is the primary definition of corrosion according to NACE International?
• Corrosion typically affects which type of materials most commonly?
• In a Wenner 4-pin configuration, how is the connection made to the pipe?
• What should you do before opening a rectifier?
• What are some sources of stray current, according to common knowledge?
• What factor can significantly affect cathodic protection efficiency over time?
• What is produced when acids disassociate in solution?
• What does polarization refer to in electrochemistry?
• Which factor is most critical when measuring potential in Close Interval Potential Surveys?
• What is the primary purpose of a cathodic protection system?
• What term describes current that does not follow the intended path?
• What does pH represent?
• What is an important factor to consider when selecting anodes for a cathodic protection system?
• Which type of anode is not designed to be used with steel structures?
• What does the term "deterioration" refer to in the context of corrosion?
• What is the impact of having a small cathode and a big anode?
• In relation to line locators, there is a direct connection with what?
• A well-coated structure is defined as what percentage or better?
• Which type of anode is highly resistant to acid attack even at pH levels less than one?
• What happens during the removal of hydrogen ions at the cathode?
• Which term refers to cables or bonds used for mitigation in cathodic protection systems?
• Which of the following methods is typically not used to prevent corrosion?
• Anode beds are usually filled with which substance?
• Which of the following is an example of an offshore reference cell?
• In an electrochemical system, which voltage drop is considered uncontrollable?
• What role does the environment play in the process of corrosion?
• Part 192 of the regulations is directly related to what?
• What is the definition of current?
• A constant voltage rectifier is normally adjusted by changing:
• What type of anodes are typically used in reinforced concrete structures?
• What action should be taken to ensure that a rectifier is safe to touch?
• Which are considered depolarizers in cathodic protection?
• Which testing method is commonly used for determining the electrical resistivity of soil?
• Which term describes a metal that has a higher concentration of oxygen and is considered more resistant to corrosion?
• What indicates a good diode during a diode check?
• What is a unique characteristic of constant potential rectifiers?
• What is the minimum negative polarized potential required with cathodic protection applied in respect to the Copper-Silver Electrode (CSE)?
• When cathodic protection is applied, what change occurs at the cathode?
• If there is a decrease in oxygen, what is likely to happen to the current requirements?
• Which of the following is true about an electrochemical corrosion cell?
• What is essential to achieve when using the Wenner Four-Pin Method?
• Voltage is described as what type of force?
• Which type of anode system is very susceptible to stray current?
• According to cathodic protection principles, what factor increases the rate of corrosion?
• What is the correct orientation for testing the Wenner 4 pin method with the pipeline?
• What type of anode system faces issues with stray current?
• In relation to cathodic protection, which component reduces corrosion by forcing electrons towards the cathode?
• What does resistance measure in an electrical circuit?
• What type of resistance should voltmeters have for accurate measurements?
• Which code provides guidance for corrosion control of underground storage tank systems through cathodic protection?
• Conductivity is equal to what?
• How does one generally measure the corrosion potential of steel?
• What type of currents vary in magnitude and often in direction?
• Can diodes be checked while the power is on in the circuit?
• What happens to current output when there is a metallic short with cathodic protection?
• What does impedance represent in AC circuits?
• According to Kirchhoff's Current Law, what happens to the current flowing into a junction?
• What is the role of a current shunt in measuring current?
• What is a galvanic anode system primarily used for?
• Which factor is most likely to accelerate the corrosion process?
• What type of environment leads to corrosion of amphoteric metals?
• What is formed when hydrogen ions are removed from the solution in electrochemical reactions?
• What must be done with the rectifier before it can be deemed safe to work on?
• Anodes at wharfs or steel pilings are considered what kind of anode?
• What is a hydrogen ion (H+) primarily produced by?
• What term describes the resistance of a conductor of unit length and cross-sectional area?
• What tool is used to find coating holidays using an electric charge?
• What is the code for external corrosion control on underground or submerged metallic piping systems?
• Ammeters are typically placed in ____ with the circuit to measure current.
• What unit is typically used to measure electric charge?
• Which instrument is commonly used to measure corrosion potential in cathodic protection?
• Where is resistance to current flow the lowest?
• Which type of electrical phenomenon involves movement through underground materials?
• What is the largest charge typically used for carbon steel pipe during exothermic welding?
• Which metal is considered more active in cathodic protection?
• What is the term for the difference in potential observed when the CP current is interrupted?
• Gas pipelines are associated with which part of the CFR?
• When the rectifier is turned off, which type of voltage remains in the system up to the breaker?
• According to Faraday's Law, what factor dictates the weight of material deposited on a cathode?
• What is one method to reduce IR drops through the electrolyte?
• What effect does decreased resistivity have on current flow in a corrosion scenario?
• What is the role of an interrupter in a rectifier setup?
• What type of environment do magnesium anodes typically operate best in?
• What does Kirchhoff's Voltage Law state regarding closed loop circuits?
• What happens to the anode when cathodic protection is applied?
• Oxygen is classified as a cathodic what?
• Corrosion is primarily caused by a difference in __________.
• What is the primary role of a zinc anode in cathodic protection systems?
• What is typically monitored to evaluate the effectiveness of a cathodic protection system?
• What does a diode check reading of 0.0001 on both sides indicate?
• What is the nominal corrosion potential of aluminum?
• In terms of cathodic protection, what does ICCP stand for?
• What does voltage (joule/coulomb) represent?
• Can CP systems be used to overcome stray current interference issues?
• Compared to zinc anodes, magnesium anodes in high resistivity soil:
• Which of the following increases the conductivity of a substance?
• ICCP technology is often used in which of the following environments?
• What is the typical potential range for magnesium anodes in cathodic protection?
• What can be a direct consequence of gas blockage in deep anode beds?
• Where are surface groundbed anodes typically installed?
• Which element is less active than hydrogen in cathodic protection systems?
• In an ICCP system, the positive terminal is connected to the?
• Magnesium anodes are known to?
• In terms of cathodic protection, what is the typical potential range for steel?
• What is considered the first line of defense against corrosion?
• What is the function of a data logger in cathodic protection surveys?
• What type of currents vary in both magnitude and direction?
• What is the role of a cathode in a galvanic cell?
• In a metallic conduction path, the flow of electrons is characterized as moving from:
• In the Galvanic Series, which element is considered the most active?
• What type of anodes are used to mitigate galvanic anode dissipation?
• Which type of metals are likely to corrode at a pH level of 8 or higher?
• What does the average soil resistivity relate to in the Wenner Four-Pin Method?
• In the Wenner 4 pin test method, how is the depth of measurement determined?
• Which anode type is typically associated with seawater in applications like water heaters?
• What does a multimeter reading of "OL" while testing a diode indicate?
• Resistivity is defined as what?
• Faraday's law of electrolysis states that metal deposited on the cathode is directly proportional to what?
• What type of material is often utilized for chemical backfill around cathodic protection anodes?
• What are the primary ions released during acid dissociation?
• What best describes an anode?
• How are atoms defined?
• What is indicated by an excess of OH- ions?
• In relation to line locators, what does conductive refer to?
• Why does current flow in a circuit?
• What is chemical bonding?
• What is the definition of anode efficiency?
• What is a primary function of cathodic protection?
• What does Ohm's Law describe?
• What is a potential consequence of using ICCP?
• What is the definition of electrochemistry?
• Why might using ICCP be potentially harmful?
• What is the purpose of mitigation bonds in stray current control?
• What happens to the pH of the environment around the cathode during cathodic protection?
• Which of the following correctly describes mitigation bonds?
• Acidic conditions are characterized by an excess of which ion?
• What is the term used for the protective layer formed during corrosion prevention treatments?
• When evaluating diode functionality, what does OL signify?
• A break in a coating is known as what?
• Which reference electrode is most commonly used on land?
• What phenomenon can cause interference in cathodic protection systems?
• Which term describes a cathode?
• In a corrosion cell, which of the following is NOT required?
• What defines the efficiency of a cathodic protection anode?
• Which parameter does not directly affect cathodic protection performance?
• Ohmeters are placed in _____ with the circuit to measure resistance.
• Deep anode installations typically have a depth of ____ in vertical installations?
• Which of the following accurately describes the function of hydroxyl ions in cathodic protection?
• What is a common cathodic reactant?
• In a series circuit, which characteristic remains constant?
• Which code pertains to underground or submerged metallic piping systems?
• In cathodic protection, which electrode is typically the cathode?
• Which of the following is a characteristic of alternating current (AC)?
• What level of voltage in an AC system is considered dangerous?
• Which scenario indicates a shorted diode during testing?
• Which branch of chemistry deals with the transfer of electric charge in chemical reactions?
• What happens to the corrosion rate as the temperature of the electrolyte increases?
• Cations are defined as what?
• The weight of any material deposited on the cathode or released from the anode is:
• What is the formula for calculating pH?
• What is the discharge mechanism of a galvanic anode?
• In cathodic protection systems, what component is typically used to provide the necessary current?
• What natural phenomena can affect telluric currents?
• In which unit is current measured?
• What happens to polarization as oxygen levels increase?
• What is the effect of a high concentration of hydrogen atoms in a solution?
• Ohm's law relates which of the following?
• What is defined as an excess of H+ ions?
• What does the use of a shunt in a measurement circuit help to determine?
• How is a constant voltage rectifier normally adjusted?
• Which of the following is NOT a feature of mitigation bonds?
• What is a common issue that may result in normal DC voltage and zero current output in an ICCP system?
• Which of the following is a source of stray current?
• According to Kirchhoff's laws, what is the relationship between power voltages and voltage drops?
• What does the external circuit in electrochemistry involve?
• In a pipe-to-soil potential profile, how is the voltmeter connected?
• What is a special concern for deep anode beds?
• To ensure safety, what should be done before working on a rectifier?
• What should be the distance between the pipe and the anodes?
• What is a characteristic feature of mixed metal oxide anodes?
• In a pipe to soil potential profile, which lead is connected to the pipe?
• What remains constant in a parallel circuit?
• In a galvanic cell, which component acts as the anode?
• What defines anions?
• What ion is produced when alkali dissociates?
• Conventional current is in the direction of:
• Which of the following factors is essential for optimal anode performance?
• In relation to line locators, what is crucial for the operation?
• Which of the following is NOT included in routine monitoring of a CP system?
• How is the input current supplied in the Wenner Four-Pin Method?
• In a corrosion cell, electrons flow in the direction of:
• Ammeters used in cathodic protection need to have what type of resistance?
• In which type of installation is the buried bare wire between the structure and the anode protected?
• What is the primary function of a cathodic protection system?
• What is a common effect of increased humidity on corrosion rates?
• Which factor is crucial for calculating power in an electric circuit?
• Which bacteria type is known to accelerate corrosion of metal pipes in clay environments?
• In what unit is power measured?
• The more ___, the greater the conductivity.
• What does NACE stand for in the context of corrosion?
• Ions are charged atoms that can be categorized as what type of charge?
• The greater the ___, the greater the corrosion rate.
• What typically will a constant voltage CP rectifier NOT have?
• In corrosion engineering, what does 'SRB' stand for?
• What is the primary definition of voltage in electrical terms?
• A stray current coming from HVDC is classified as?